78 Zeilen
4 KiB
Markdown
78 Zeilen
4 KiB
Markdown
Before you run **mailcow: dockerized**, there are a few requirements that you should check:
|
||
|
||
!!! warning
|
||
When running mailcow: dockerized on a Debian 8 (Jessie) box, you should [switch to kernel 4.9 from Jessie backports](https://packages.debian.org/jessie-backports/linux-image-amd64) to avoid a bug when running Docker containers with *healthchecks*! For more details read: [github.com/docker/docker/issues/30402](https://github.com/docker/docker/issues/30402)
|
||
|
||
!!! info
|
||
- mailcow: dockerized requires [some ports](#default-ports) to be open for incomming connections, so make sure that your firewall is not bloking these. Also make sure that no other application is interferring with mailcow's configuration.
|
||
- A correct DNS setup is crucial to every good mailserver setup, so please make sure you got at least the [basics](dns/#the-minimal-dns-configuration) covered bevore you begin!
|
||
- Make sure that your system has a correct date and [time setup](#date-and-time). This is crucial for stuff like two factor TOTP authentication.
|
||
|
||
## Minimum System Resources
|
||
|
||
Please make sure that your system has at least the following resources:
|
||
|
||
| Resource | mailcow: dockerized |
|
||
| ----------------------- | --------------------- |
|
||
| CPU | 1 GHz |
|
||
| RAM Â Â Â Â Â Â Â Â Â Â | 1 GiB Â Â Â Â |
|
||
| Disk | 5 GiB (without mails) |
|
||
| System Type | x86_64 |
|
||
|
||
## Firewall & Ports
|
||
|
||
Please check if any of mailcow's standard ports are open and not blocked by other applications:
|
||
|
||
```
|
||
# netstat -tulpn | grep -E -w '25|80|110|143|443|465|587|993|995'
|
||
```
|
||
|
||
If this command returns any results please remove or stop the application running on that port. You may also adjust mailcows ports via the `mailcow.conf` configuration file.
|
||
|
||
### Default Ports
|
||
|
||
If you have a firewall already up and running please make sure that these ports are open for incoming connections:
|
||
|
||
| Service | Protocol | Port | Container | Variable |
|
||
| --------------------|:--------:|:-------|:----------------|--------------------------------|
|
||
| Postfix SMTP | TCP | 25 | postfix-mailcow | `${SMTP_PORT}` |
|
||
| Postfix SMTPS | TCP | 465 | postfix-mailcow | `${SMTPS_PORT}` |
|
||
| Postfix Submission | TCP | 587 | postfix-mailcow | `${SUBMISSION_PORT}` |
|
||
| Dovecot IMAP | TCP | 143 | dovecot-mailcow | `${IMAP_PORT}` |
|
||
| Dovecot IMAPS | TCP | 993 | dovecot-mailcow | `${IMAPS_PORT}` |
|
||
| Dovecot POP3 | TCP | 110 | dovecot-mailcow | `${POP_PORT}` |
|
||
| Dovecot POP3S | TCP | 995 | dovecot-mailcow | `${POPS_PORT}` |
|
||
| Dovecot ManageSieve | TCP | 4190 | dovecot-mailcow | `${SIEVE_PORT}` |
|
||
| HTTP(S) | TCP | 80/443 | nginx-mailcow | `${HTTP_PORT}` / `${HTTPS_PORT}` |
|
||
|
||
## Date and Time
|
||
|
||
To ensure that you have the correct date and time setup on your system, please check the output of `timedatectl status`:
|
||
|
||
```
|
||
$ timedatectl status
|
||
Local time: Sat 2017-05-06 02:12:33 CEST
|
||
Universal time: Sat 2017-05-06 00:12:33 UTC
|
||
RTC time: Sat 2017-05-06 00:12:32
|
||
Time zone: Europe/Berlin (CEST, +0200)
|
||
NTP enabled: yes
|
||
NTP synchronized: yes
|
||
RTC in local TZ: no
|
||
DST active: yes
|
||
Last DST change: DST began at
|
||
Sun 2017-03-26 01:59:59 CET
|
||
Sun 2017-03-26 03:00:00 CEST
|
||
Next DST change: DST ends (the clock jumps one hour backwards) at
|
||
Sun 2017-10-29 02:59:59 CEST
|
||
Sun 2017-10-29 02:00:00 CET
|
||
```
|
||
|
||
The lines `NTP enabled: yes` and `NTP synchronized: yes` indicate wether you have NTP enabled and if it's synchronized.
|
||
|
||
To enable NTP you need to run the command `timedatectl set-ntp true`. You also need to edit your `/etc/systemd/timesyncd.conf`:
|
||
|
||
```
|
||
# vim /etc/systemd/timesyncd.conf
|
||
[Time]
|
||
Servers=0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org 3.pool.ntp.org
|
||
```
|